part # description m-8870-01 18-pin plastic dip m-8870-01sm 18-pin plastic soic m-8870-01smtr 18-pin plastic soic, tape and reel m-8870-02 18-pin plastic dip, power-down, option m-8870-02sm 18-pin plastic soic, power-down, option m-8870-02t 18-pin plastic soic, power-down option, tape and reel www.clare.com ds-m8870-r3 m-8870 dtmf receiver 1 block diagram pin configuration ordering information features low power consumption adjustable acquisition and release times central office quality and performance power-down and inhibit modes (-02 only) inexpensive 3.58 mhz time base single 5 volt power supply dial tone suppression applications telephone switch equipment remote data entry paging systems personal computers credit card systems description the m-8870 is a full dtmf receiver that integrates both bandsplit filter and decoder functions into a single 18-pin dip or soic package. manufactured using cmos process technology, the m-8870 offers low power consumption (35 mw max) and precise data handling. its filter section uses switched capacitor technology for both the high and low group filters and for dial tone rejection. its decoder uses digital counting techniques to detect and decode all 16 dtmf tone pairs into a 4-bit code. external component count is minimized by provision of an on-chip differential input amplifier, clock generator, and latched tri-state inter- face bus. minimal external components required include a low-cost 3.579545 mhz color burst crystal, a timing resistor, and a timing capacitor. the m-8870-02 provides a ?ower-down?option which, when enabled, drops consumption to less than 0.5 mw. the m-8870-02 can also inhibit the decoding of fourth column digits (see tone decoding table on page 5).
operating characteristics - gain setting amplifier parameter symbol min typ max units test conditions input leakage current i n - 100 - na v ss < v in < v dd input resistance r in 4--m ? - input offset voltage v os - 25-mv - power supply rejection psrr 50 - - db 1 khz common mode rejection cmrr 55 - - db -3.0v < v in < 3.0v dc open loop voltage gain a vol 60 - - db - open loop unity gain bandwidth f c 1.2 1.5 - mhz - output voltage swing v o 3.5 - - v p-p rl 100 k ? to v ss tolerable capacitive load (gs) c l - - 100 pf - tolerable resistive load (gs) r l --50k ? - common mode range v cm 2.5 - - v p-p no load *typical figures are at 25? and are for design aid only; not guaranteed and not subject to production testing. notes: 1. all voltages referenced to v ss unless otherwise noted. for typical values, v dd = 5.0v, v ss = 0v, ta = 25?. dc characteristics parameter symbol min typ max units test conditions operating supply voltage v dd 4.75 - 5.25 v - operating supply current i dd - 3.0 7.0 ma - standby supply current (see note 3) i dd q - - 100 ? pd=v dd power consumption p o - 15 35 mw f = 3.579 mhz, v dd = 5.0 v low level input voltage v il - - 1.5 v - high level input voltage v ih 3.5 - - v - input leakage current i ih /i il - 0.1 - a v in = v ss or v dd (see note 2) pullup (source) current on oe i so - 6.5 15.0 ? oe = 0 v input impedance, signal inputs 1, 2 r in 810-m ? @ 1 khz steering threshold voltage v tst 2.2 - 2.5 v - low level output voltage v ol - - 0.03 v no load high level output voltage v oh v dd - 0.03 - - v no load output low (sink) current i ol 1.0 2.5 - ma v out = 0.4 v output high (source) current i oh 0.4 0.8 - ma v out = v dd - 0.4 v output voltage v ref v ref 2.4 - 2.7 v no load output resistance v ref r or -10-k ? - *typical figures are at 25? and are for design aid only; not guaranteed and not subject to production testing. absolute maximum ratings parameter symbol value power supply voltage (v dd - v ss )v dd 6.0 v max voltage on any pin v dc v ss -0.3, vdd +0.3 current on any pin i dd 10 ma max operating temperature t a -40? to + 85? storage temperature t s -65? to + 150? note: exceeding these ratings may cause permanent damage. functional operation under these conditions is not implied. www.clare.com 2 m-8870 rev. 3 absolute maximum ratings are stress ratings. stresses in excess of these ratings can cause permanent damage to the device. functional operation of the device at these or any other conditions beyond those indicated in the opera- tional sections of this data sheet is not implied. exposure of the device to the absolute maximum ratings for an extend- ed period may degrade the device and effect its reliability.
m-8870 www.clare.com 3 rev. 3 basic steering circuit single-ended input configuration functional description m-8870 operating functions (see block diagram on page 1) include a bandsplit filter that separates the high and low tones of the received pair, and a digital decoder that verifies both the frequency and duration of the received tones before passing the resulting 4-bit code to the output bus. filter the low and high group tones are separated by apply- ing the dual-tone signal to the inputs of two 6th order switched capacitor bandpass filters with bandwidths that correspond to the bands enclosing the low and high group tones. the filter also incorporates notches at 350 and 440 hz, providing excellent dial tone rejec- tion. each filter output is followed by a single-order switched capacitor section that smooths the signals prior to limiting. signal limiting is performed by high- gain comparators provided with hysteresis to prevent detection of unwanted low-level signals and noise. the comparator outputs provide full-rail logic swings at the frequencies of the incoming tones. decoder the m-8870 decoder uses a digital counting tech- nique to determine the frequencies of the limited tones and to verify that they correspond to standard dtmf frequencies. a complex averaging algorithm is used to protect against tone simulation by extraneous signals (such as voice) while tolerating small frequency varia- tions. the algorithm ensures an optimum combination of immunity to talkoff and tolerance to interfering sig- nals (third tones) and noise. when the detector rec- ognizes the simultaneous presence of two valid tones (known as signal condition), it raises the early steering flag (est). any subsequent loss of signal condition will cause est to fall. steering circuit before a decoded tone pair is registered, the receiver checks for a valid signal duration (referred to as char- acter-recognition-condition). this check is performed by an external rc time constant driven by est. a logic high on est causes vc (see block diagram on page 1) to rise as the capacitor discharges. provided that sig- nal condition is maintained (est remains high) for the validation period (t gtf ), v c reaches the threshold (v tst ) of the steering logic to register the tone pair, thus latch- ing its corresponding 4-bit code (see dc characteristics on page 2) into the output latch. at this point, the gt output is activated and drives v c to v dd . gt continues to drive high as long as est remains high. finally, after a short delay to allow the output latch to settle, the delayed steering output flag (std) goes high, signaling that a received tone pair has been registered. the contents of the output latch are made available on the 4-bit output bus by raising the three- state control input (oe) to a logic high. the steering circuit works in reverse to validate the interdigit pause between signals. thus, as well as rejecting signals too short to be considered valid, the receiver will tolerate signal interruptions (dropouts) too short to be consid- ered a valid pause. this capability, together with the ability to select the steering time constants externally, allows the designer to tailor performance to meet a wide variety of system requirements.
pin functions pin name description 1 in+ non-inverting input connections to the front-end differential amplifier. 2 in- inverting input 3 gs gain select. gives access to output of front-end amplifier for connection of feedback resistor. 4v ref reference voltage output (nominally vdd/2). may be used to bias the inputs at mid-rail. 5 inh* inhibits detection of tones representing keys a, b, c, and d. 6 pd* power down. logic high powers down the device and inhibits the oscillator. internal pulldown. 7 osc1 clock input 3.579545 mhz crystal connected between these pins completes the internal oscillator. 8 osc2 clock output 9 vss negative power supply (normally connected to 0 v). 10 oe tri-statable output enable (input). logic high enables the outputs q1 - q4. internal pullup. 11-14 q1, q2, tri-statable data outputs. when enabled by oe, provides the code corresponding to the last valid tone pair q3, q4 received (see tone decoding table on page 5). 15 std delayed steering output. presents a logic high when a received tone pair has been registered and the output latch is updated. returns to logic low when the voltage on st/gt falls below vtst. 16 est early steering output. presents a logic high immediately when the digital algorithm detects a recognizable tone pair (sign al condition). any momentary loss of signal condition will cause est to return to a logic low. 17 st/gt steering input/guard time output (bidirectional). a voltage greater than vtst detected at st causes the device to regist er the detected tone pair and update the output latch. a voltage less than vtst frees the device to accept a new tone pair. the gt output acts to reset the external steering time constant, and its state is a function of est and the voltage on st. (see common crystal connection on page 5). 18 v dd positive power supply. (normally connected to +5v.) * -02 only. connect to v ss for -01 version www.clare.com 4 m-8870 rev. 3 guard time adjustment where independent selection of signal duration and interdigit pause are not required, the simple steering circuit of basic steering circuit is applicable. component values are chosen according to the formu- la: t rec = t dp + t gtp t gtp @ 0.67 rc the value of tdp is a parameter of the device and trec is the minimum signal duration to be recognized by the receiver. a value for c of 0.1 ? is recommend- ed for most applications, leaving r to be selected by the designer. for example, a suitable value of r for a t rec of 40 ms would be 300 k ? . a typical circuit using this steering configuration is shown in the single - ended input configuration on page 4. the timing requirements for most telecommunication applications are satisfied with this circuit. different steering arrange- ments may be used to select independently the guard times for tone-present (t gtp ) and tone-absent (t gta ). this may be necessary to meet system specifications that place both accept and reject limits on both tone duration and interdigit pause. guard time adjustment also allows the designer to tai- lor system parameters such as talkoff and noise immu- nity. increasing t rec improves talkoff performance, since it reduces the probability that tones simulated by speech will maintain signal condition long enough to be registered. on the other hand, a relatively short t rec with a long t do would be appropriate for extremely noisy environments where fast acquisition time and immunity to dropouts would be required. design infor- mation for guard time adjustment is shown in the guard time adjustment below. power-down and inhibit mode (-02 only) a logic high applied to pin 6 (pd) will place the device into standby mode to minimize power consumption. it figure 5 guard time adjustment
tone decoding flow fhigh key (ref.) oe q4 q3 q2 q1 697 1209 1 h 0 0 0 1 697 1336 2 h 0 0 1 0 697 1477 3 h 0 0 1 1 770 1209 4 h 0 1 0 0 770 1336 5 h 0 1 0 1 770 1477 6 h 0 1 1 0 852 1209 7 h 0 1 1 1 852 1336 8 h 1 0 0 0 852 1477 9 h 1 0 0 1 941 1336 0 h 1 0 1 0 941 1209 s h 1 0 1 1 941 1477 # h 1 1 0 0 697 1633 a h 1 1 0 1 770 1633 b h 1 1 1 0 852 1633 c h 1 1 1 1 941 1633 d h 0 0 0 0 any any any l z z z z l = logic low, h = logic high, z = high impedance m-8870 www.clare.com 5 rev. 3 differential input configuration common crystal connection stops the oscillator and the functioning of the filters. on the m-8870-01 models, this pin is tied to ground (logic low). inhibit mode is enabled by a logic high input to pin 5 (inh). it inhibits the detection of 1633 hz. the output code will remain the same as the previous detected code (see pin functions table on page 4). on the m- 8870-01 models, this pin is tied to ground (logic low). input configuration the input arrangement of the m-8870 provides a dif- ferential input operational amplifier as well as a bias source (v ref ) to bias the inputs at mid-rail. provision is made for connection of a feedback resistor to the op-amp output (gs) for gain adjustment. in a single-ended configuration, the input pins are connected as shown in the single - ended input configuration on page 3 with the op-amp connected for unity gain and v ref biasing the input at 1/2v dd . the differential input configuration bellow permits gain adjustment with the feedback resistor r 5 . dtmf clock circuit the internal clock circuit is completed with the addition of a standard 3.579545 mhz television color burst crys- tal. the crystal can be connected to a single m-8870 as shown in the single - ended input configuration on page 3, or to a series of m-8870s. as illustrated in the common crystal connection below, a single crystal can be used to connect a series of m-8870s by cou- pling the oscillator output of each m-8870 through a 30 pf capacitor to the oscillator input of the next m-8870.
www.clare.com 6 m-8870 rev. 3 ac characteristics parameter symbol min typ* max units notes valid input signal levels (each tone - -29 - +1 dbm 1,2,3,4,5,8 of composite signal) - 27.5 - 869 mvrms positive twist accept - - - 10 db 2,3,4,8 negative twist accept - - - 10 db frequency deviation accept limit - - - 1.5% + 2 hz nom. 2,3,5,8,10 frequency deviation reject limit - 3.5% - - nom. 2,3,5 third tone tolerance - -25 -16 - db 2,3,4,5,8,9,13,14 noise tolerance - - -12 - db 2,3,4,5,6,8,9 dial tone tolerance - +18 +22 - db 2,3,4,5,7,8,9 tone present detection time t dp 5 8 14 ms see timing diagram on page 7 tone absent detection time t da 0.5 3 8.5 ms minimum tone duration accept t rec - - 40 ms user adjustable (see basic steering maximum tone duration reject t rec 20 - - ms circuit and guard time adjustment minimum interdigit pause accept t id - - 40 ms on pages 3 and 4.) maximum interdigit pause reject t do 20 - - ms propagation delay (st to q) t pq - 6 11 ? oe = vdd propagation delay (st to std) t pstd - 9 16 ? output data setup (q to std) t qstd - 4.0 - s propagation delay (oe to q), enable t pte -5060 ns r l = 10 k ? , c l = 50 pf propagation delay (oe to q), disable t ptd - 300 - ns crystal clock frequency f clk 3.5759 3.5795 3.5831 mhz - clock output (osc2), capacitive load c lo --30 pf - all voltages referenced to v ss unless otherwise noted. for typical values v dd = 5.0 v, v ss = 0 v, ta = 25?, f clk = 3.579545 mhz. *typical figures are at 25? and are for design aid only; not guaranteed and not subject to production testing. notes: 1. dbm = decibels above or below a reference power of 1 mw into a 600 ? load. 2. digit sequence consists of all 16 dtmf tones. 3. tone duration = 40 ms. tone pause = 40 ms. 4. nominal dtmf frequencies are used, measured at gs. 5. both tones in the composite signal have an equal amplitude. 6. bandwidth limited (0 to 3 khz) gaussian noise. 7. the precise dial tone frequencies are (350 and 440 hz) 2%. 8. for an error rate of better than 1 in 10,000. 9. referenced to lowest level frequency component in dtmf signal. 10. minimum signal acceptance level is measured with specified maximum frequency deviation. 11. input pins defined as in+, in-, and oe. 12. external voltage source used to bias v ref . 13. this parameter also applies to a third tone injected onto the power supply. 14. referenced to single - ended input configuration on page 3. input dtmf tone level at -28 dbm.
m-8870 www.clare.com 7 rev. 3 timing diagram explanation of events (a) tone bursts detected, tone duration invalid, outputs not updated. (b) tone #n detected, tone duration valid, tone decoded and latched in outputs. (c) end of tone #n detected, tone absent duration valid, outputs remain latched until next valid tone. (d) outputs switched to high impedance state. (e) tone #n + 1 detected, tone duration valid, tone decoded and latched in outputs (currently high impedance). (f) acceptable dropout of tone #n + 1, tone absent duration invalid, outputs remain latched. (g) end of tone #n + 1 detected, tone absent duration valid, outputs remain latched until next valid tone. explanation of symbols vin dtmf composite input signal. est early steering output. indicates detection of valid tone frequencies. st/gt steering input/guard time output. drives external rc timing circuit. q1 - q4 4-bit decoded tone output. std delayed steering output. indicates that valid frequencies have been present/ absent for the required guardtime, thus constituting a valid signal. oe output enable (input). a low level shifts q1 - q4 to its high impedance state. t rec maximum dtmf signal duration not detected as valid. t rec minimum dtmf signal duration required for valid recognition. t id minimum time between valid dtmf signals. t do maximum allowable dropout during valid dtmf signal. t dp time to detect the presence of valid dtmf signals. t da time to detect the absence of valid dtmf signals. t gtp guard time, tone present. t gta guard time, tone absent.
tolerances for 18 - pin dip inches metric (mm) min max min max a .0926 .1043 2.35 2.65 a1 .0040 .0118 .10 .30 b .013 .020 .33 .51 d .4469 .4625 11.35 11.75 e .2914 .2992 7.4 7.6 e .050 bsc 1.27 bsc h .394 .419 10.00 10.65 l .016 .050 .40 1.27 tolerances for 18 - pin dip inches metric (mm) min max min max a - .210 - 5.33 a1 .015 - .38 - b .014 .022 .36 .56 b2 .045 .070 1.1 1.7 c .008 .014 .20 .36 d .880 .920 23.35 23.37 e .300 .325 7.62 8.26 e1 .240 .280 6.10 7.11 e .100 bsc 2.54 bsc ec 0 15 0 15 l .115 .150 2.92 3.81 www.clare.com 8 m-8870 rev. 3 figure 9 mechanical dimensions dimensions mm (inches)
worldwide sales offices clare locations clare headquarters 78 cherry hill drive beverly, ma 01915 tel: 1-978-524-6700 fax: 1-978-524-4900 toll free: 1-800-27-clare clare switch division 4315 n. earth city expressway earth city, mo 63045 tel: 1-314-770-1832 fax: 1-314-770-1812 clare micronix division 145 columbia aliso viejo, ca 92656-1490 tel: 1-949-831-4622 fax: 1-949-831-4628 sales offices americas americas headquarters clare 78 cherry hill drive beverly, ma 01915 tel: 1-978-524-6700 fax: 1-978-524-4900 toll free: 1-800-27-clare eastern region clare 603 apache court mahwah, nj 07430 tel: 1-201-236-0101 fax: 1-201-236-8685 toll free: 1-800-27-clare central region clare canada ltd. 3425 harvester road, suite 202 burlington, ontario l7n 3n1 tel: 1-905-333-9066 fax: 1-905-333-1824 western region clare 1852 west 11th street, #348 tracy, ca 95376 tel: 1-209-832-4367 fax: 1-209-832-4732 toll free: 1-800-27-clare canada clare canada ltd. 3425 harvester road, suite 202 burlington, ontario l7n 3n1 tel: 1-905-333-9066 fax: 1-905-333-1824 europe european headquarters cp clare nv bampslaan 17 b-3500 hasselt (belgium) tel: 32-11-300868 fax: 32-11-300890 france clare france sales lead rep 99 route de versailles 91160 champlan france tel: 33 1 69 79 93 50 fax: 33 1 69 79 93 59 germany clare germany sales activecomp electronic gmbh mitterstrasse 12 85077 manching germany tel: 49 8459 3214 10 fax: 49 8459 3214 29 italy c.l.a.r.e.s.a.s. via c. colombo 10/a i-20066 melzo (milano) tel: 39-02-95737160 fax: 39-02-95738829 sweden clare sales comptronic ab box 167 s-16329 sp?nga tel: 46-862-10370 fax: 46-862-10371 united kingdom clare uk sales marco polo house cook way bindon road taunton uk-somerset ta2 6bg tel: 44-1-823 352541 fax: 44-1-823 352797 asia/pacific asian headquarters clare room n1016, chia-hsin, bldg ii, 10f, no. 96, sec. 2 chung shan north road taipei, taiwan r.o.c. tel: 886-2-2523-6368 fax: 886-2-2523-6369 http://www.clare.com clare, inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. neither circuit patent licenses nor indemnity are expressed or implied. except as set forth in clare s standard terms and conditions of sale, clare, inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limit- ed to, the implied warranty of merchantability, fitness for a partic- ular purpose, or infringement of any intellectual property right. the products described in this document are not designed, intended, authorized or warranted for use as components in sys- tems intended for surgical implant into the body, or in other appli- cations intended to support or sustain life, or where malfunction of clare s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. clare, inc. reserves the right to discontinue or make changes to its products at any time without notice. specification: ds-m-8870-r3 ?opyright 2001, clare, inc. all rights reserved. printed in usa. 7/25/01
|
